Elimia DOL Magnetic Motor Starter 20 HP 120V 23-32A Hinged Steel Enclosure (40)

Description

Please call us if you have any questions.  We want you to get the right equipment - 1-855-4Elimia.
This is for a new magnetic motor starter. Motor starters provide protection for your equipment above and beyond normal circuit breakers.
Elimia DOL motor starters are pre-wired for magnetic latching. This means that in the event of a power blink your starter will unlatch and open the contacts. When power returns your starter will require restarting which enables safe machine starts.
Pre-wired industrial grade metal bezel start stop switch with LED ON indicator.
Easy installation, just bring power in and power out. No switches to wire up!
The unit will arrive completely assembled in a real nice NEMA
12
steel enclosure,
dust and water tight, with a hinge door.
Model Number: DOL 23 - 32 -120 NEMA 12
Model Explanation:
DOL = Latching Start/Stop push button
23 - 32  = Overload Size
110 - 120 = Coil Voltage
NEMA 12 = Enclosure type
Sized for 20 HP @ 480V 3 phase or 10 HP @ 230V 3 phase.  Verify with your motor.
Our motor starters use UL certified IEC type components.
IEC type motor starters are made up of primarily two parts. A contactor and overload device. Both devices have maximum ratings and the overload has maximum and minimum ratings. You should choose a motor starter that fits both criteria. If you need help please email or call, we will be glad to assist.
To size your starter properly you must determine the following:
-Three phase or Single phase
-Supply voltage ie. 120V; 208V; 240V; 480V; 600V
-Machine single motor HP
-Motor FLA (full load Amps)
-Application, what type of machine you running
We recommend that for certain machines to use a contactor the is oversized. Meaning if you have a 10 HP machine and the contactor is rated for not more than 10 HP, we recommend you go up one contactor size to a 15 HP contactor. This is recommended for hard starting machines and machines that are started and stopped frequently. Such as air compressors, blowers, vacuums etc... Also, you must size the contactor based on your supply voltage. A contactor rated for 15 HP at 240V three phase will be rated for less HP at 480V. Exceeding the contactors rating will dramatically reduce its life.
If your supply Voltage is 208V and you w
ant
to use your supply power to power the contactor coil...  Our 230/240V coils are rated down to 196 Volts.  Now, under most cases our standard 230/240V coil will work flawlessly on 208V systems.  But, if your machine is very large for your electrical service OR your wiring run is long or undersized I recommend using a separate 120V source for the coil power.
Ratings of contactor used in this starter, do not exceed ratings:
Size 40
1 phase- 7.5 HP @ 240 VAC Max FLA 40 Amps
3 phase- 15 HP @ 200 VAC Max FLA 48.3 Amps
3 phase- 20 HP @ 240 VAC Max FLA 54 Amps
3 phase- 25 HP @ 460 VAC Max FLA 34 Amps
3 phase- 25 HP @ 600 VAC Max FLA 27 Amps
Control voltage is
120
VAC
and is pre-wired. (Note: the power source for the control wiring of this starter is pre-wired and sourced from your feeder wiring directly on the line side of the starter.  You will not need to pull in a separate power source for the controls).
The control voltage is the voltage used to activate the coil of the contactor. In the simplest install you will want a coil voltage the same as your power supply. But is some cases you might want the control voltage to be different for a host of reasons.
All components used in our assemblies are UL Certified.
The overload will have an adjustable Amperage range. Your overload choice is based on your machines FLA. If your machine motor has a FLA of 10 Amps at your supply voltage then you should choose the overload where 10 Amp falls within the adjustable range. For a 10 Amp FLA we would recommend overload 9 - 13 Amps.
Our overloads can be set for manual or automatic reset operation. The overload control is pre-wired by Elimia in a way that trips the starter. This is done to protect your equipment and is one of the main purposes of a motor starter.
Our standard overload is thermal type class 10A. Special Electronic overload is available.  Please call.
If you are ordering this motor starter for a single phase application, please let us know. There is a slight wiring change that we do that sets it up for single phase.
Components mounted on a easy to remove back plate.
To size your starter properly you must determine the following:
-Three phase or Single phase
-Supply voltage ie. 120V; 208V; 240V; 480V; 600V
-Machine single motor HP
-Motor FLA (full load Amps)
-Application, what type of machine you running
Overload can be set for manual or automatic reset operation.
Components mounted on a easy to remove back plate.
Enclosure is NEMA 12/13 made in USA by Wiegmann.  Provides protection from water/dust/oil.  UL listed to 600V.
Enclosure size is 10 x 8 x 6 or 10 x 8 x 5 or 10 x 8 x 4.
90 day replacement Elimia warranty.
Great price!
We have pre-wired DOL motor starters available from 0 HP to 200 HP.
Please call 256-528-7120 for more info or if we can help sizing a starter.
Please note: We stock an extensive inventory of contactors, overloads, enclosures, switches etc...  We do not stock preassembled units due to the massive possible combination of products.  All motor starters and assemblies are built to order.  Lead time may vary from same day to three days.
We sell many many industrial electrical assemblies every week.  Our customers really appreciate our products, services and low prices, they come back time again.
Guarantee: Satisfaction Guaranteed! If you are not happy with your purchase within two weeks of arrival you can return it. No restocking fee! Offer excludes shipping and eBay fees. Items identified in the main description "as is" do not have a guarantee to work.
Buyers:  Potential buyers registered outside the USA must get approval before bidding UNLESS the listing indicates them as a ship to location.  Most small items are now available for Worldwide shipping.
At store pick up and shipping:  There is no charge for on-sight pickup.
Please note: All items should be professionally inspected and tested prior to installation or use. We are not liable for damages, injuries or death relating to our products.
Payments:  We accept Paypal and Credit Card payments.  Credit card payments are only accepted over the phone.
We reserve the right to refuse payment from buyers registered in foreign countries or locations with non corresponding ship to addresses.  Additionally, we reserve the right to refuse payment from any buyer which will feel is acting in a possible malicious manner.
Feedback:  Once you are satisfied with your purchase please leave us feedback. If you have any problem with the transaction or product, please contact us.